The makiwara is a core implement in any classical karate training program. Simple in its design, the specific function of the makiwara makes it an invaluable companion.

Good karate training involves striking, and freestanding or hanging heavy bags are an important component of that. However, the makiwara provides progressive resistance (the harder you hit it, the more it pushes back). This is critical in learning how to transmit power and feel the strength of your body’s structure.

Makiwara training should be conducted slowly, methodically, and under proper supervision.

How to Build Your Makiwara

Needed Materials (Purchased at Lowe’s or an Equivalent Hardware Store)

  • Red oak post – This is the wood you’ll use for the striking post itself. An eight foot piece will probably do the trick, but if that is too difficult to transport than you can get a six foot and four foot piece.
  • Plywood base – Make sure to get a sanded base piece that is at least 1/2″ thick. You’ll likely need to sand it down a bit more to make it suitable for bare feet. If you can transport a 4’x8′ that will be ideal because you can cut it in half and double the thickness of your platform. However, some Lowe’s stores sell 4’x4′ pieces which makes transport much easier. I put 4’x4′ pieces into my Subaru Outback.
  • Oak trim – This trim will go on the bottom side of your base, providing space between the plywood and floor (allowing you to secure screws via lug nuts.
  • Main bracket – You’ll use this to secure the striking board to the base.
  • Assorted wood or drywall screws – If you don’t have a variety of screws already, pick some of these up. You’ll want a variety of sizes and thicknesses to suit your specific build.
  • Makiwara top – The industry-standard for makiwara tops is Shureido but they can be difficult to get outside of Okinawa. Instead, I recommend a combination of mouse pads and either duct tape or leather wrapping (depending on how crafty you are feeling).
  • Mobility Wheels (Optional) – If you’d like to move your makiwara around more easily, you can secure these wheels to the back of the base.

Step 1 – Prepare Your Striking Board

There are two traditional methods for preparing your makiwara board. The first is creating taper. You generally start with a thicker board and taper it toward the top which provides a solid base with springiness at the top. This method requires a table saw and a skilled hand, so I opt for option #2, which is compounded board pieces.

Purchasing the red oak board that is 3/4″ thick will allow you to double and then triple the thickness toward the bottom. All you’ll need is a typical hand saw or circular saw and some screws.

So here we go!

  1. Measure the height you want your makiwara to stand. It should be about the height of your shoulder or slightly lower. Remember, makiwara is a custom training tool so there is no standard height. For example, I’m 5’10” so my primary maki board is 55″ tall. Take your 6′ or 8′ red oak board and mark it to your desired height. Make your first cut.
  2. The next board will support the main board. This second board should be about half the height of the first. The taller your second board, the more resistance you’ll experience while punching. So gauge your intended usage accordingly. If you are a veteran of makiwara punching, feel free to make the second board higher so you get stiffer resistance. If you are newer to makiwara training, make it a little less than half height. I personally went with 27.5″ to augment my 55″ initial post. after marking your second board, make your second cut.
  3. Secure your second board to your first board. Make sure that you create a flush bottom where the post will stand. I personally selected screws that would not penetrate all the way through both boards and stick out the back end.
  4. Prepare your final board. This third board will provide a solid base. Make sure it is taller than the brackets you intend to use. For example, my third board is 17.5″ tall. Cut this board and secure it to the other two boards. Be sure to maintain that flush bottom where the post will stand.

Step 2 – Prepare your Platform

Many people choose to secure their makiwara to the structure of their home. You can do so by using a bracer block and screwing directly into your home’s studs. The downside to this method is that the makiwara is not mobile and the vibration from striking can sometimes rattle through the home. I have opted to make a mobile platform that utilizes body weight to keep the post and platform in place.

  1. If you purchased a 4’x8′ piece of plywood, I recommend cutting it in half so you have two even 4’x4′ pieces. If you were lucky enough to find 4’x4′ pieces for sale you are ready to go.
  2. Sand your plywood surfaces with a finishing grit sandpaper. This should prevent any instances of splinters. You may choose to finish the wood as well to your liking but I left mine unfinished.
  3. Secure your plywood base pieces together. I utilized screws that would not penetrate all the way through both boards so as to avoid damaging my mats and floors while moving the makiwara around. I was also sure to embed the heads of the screws just below the wood surface so as not to catch my foot on them while moving around.
  4. Attach a trim piece of wood around the edges and possibly once piece down the middle (to avoid sagging). This trim will create a small gap between the bottom of your plywood and the floor, allowing you to screw all the way through the plywood and use securing bolts on the opposite side for your post mount.

Step 3 – Secure Your Brackets to the Post and Platform

Bracketing is where you’ll see the most variance in makiwara construction. I’ve elected to use a sturdy fence post bracket purchase at Lowe’s. This provides good 360 degree security, although it required a filler block when fastening the post. To use a similar bracket, follow these steps:

  1. Begin by measuring the width of your platform and finding the center. Mark the center. Now measure 5-6″ inches away from the edge of your platform so that you can screw the base in without hitting your trim pieces. Remember, you’ll want the base screws to go all the way through so you can secure them on the underside with nuts.
  2. Once the center location is established, place your fence post bracket on the base. Mark the four holes where the lug screws will go.
  3. Pre-drill the four holes at the same width as your lug screws. Go all the way through your base boards.
  4. Place your lug screws through a washer and the fence post bracket. Secure the lug screws on the bottom side (I recommend a socket wrench).

Note: Depending on your style, you may be advised to have a slight angle forward in your makiwara post. Determine that before securing your base so you can add a wedge (or plane the wood) to create the desired angle.

Step 4 (Optional) – Add Mobility Wheels

For ease-of-transport I added wheels to the back end of my board. It has proven very useful and I recommend it. I can easily tilt and roll the board wherever I need it and it does not damage my tatami mats. Here are some steps:

  1. If you have any leftover trim pieces, cut two even pieces.
  2. Measure them equidistant from the center of the base.
  3. Line them evenly with the edge of the board and secure via screws.
  4. Measure the center of those leftover pieces and pre-drill holes for your wheels.
  5. Secure the wheels vertically.

Step 5 – Create your Maki Top

This next step will vary depending on how fancy you want to get. If you are lucky enough to have a pre-made makiwara top, just slip it on and you are ready to go. Maki tops are usually not glued, screwed, or secured. They can slip on and off. This is handy if you want to have a dojo where everyone can utilize their own top or if you need to protect the top from outdoor elements.

Presuming you do not have a pre-fabricated top, the easiest approach is as follows:

  1. Take 1,2, or 3 mouse pads and wrap them around your maki board (flat part in front, edges around back. If you need to trim the mousepads so they lay flat, go ahead and do so. The newer you are to maki training, the more padding you should use.
  2. Take duct tape and wrap it around the mouse pads until you have fully covered them. Then tape around the top as well to ensure the pad does not slip down. Finally, tape around the circumference of the pad again. Using this method, you should be able to slide the pad on and off at your discretion.  One word of caution about duct tape – it is tackier than leather. If your skin hasn’t been developed by maki training you may find it pulls and tears a bit at your skin. Explore other surfaces if you are concerned about this.
  3. If you are feeling crafty, you can purchase a piece of leather and secure that to the mousepads instead. You can utilize glue or screws around back to keep everything secure. When I was creating my outdoor makiwara I simply screwed the top leather on via the back of the board (making sure the screws were short enough not to poke through the front). I then put a bucket over top of the maki when it wasn’t in use to prevent weather damage. That being said, leaving the top on when outside does shorten the lifespan of the top, which is why it is convenient to be able to take it on and off.

That’s it! Congratulations, you now have a highly functional makiwara. Please seek advanced guidance on its proper use and enjoy.